MQB TPMS High retrofit: Difference between revisions

From mr-fix.info Wiki
Jump to navigation Jump to search
 
(12 intermediate revisions by the same user not shown)
Line 11: Line 11:
<ref>https://www.drive2.ru/parts/vag/5q0907273b/B9bkAEAFz1g</ref>
<ref>https://www.drive2.ru/parts/vag/5q0907273b/B9bkAEAFz1g</ref>


* Module (J533)
* Module (J502)
** <code>5Q0-907-273</code> - 433MHz version
** <code>5Q0-907-273-B</code> / <code>5Q0-907-273-F</code> - 433MHz version
** <code>5Q0-907-273</code> - 315MHz version
** <code>5Q0-907-273-C</code> / <code>5Q0-907-273-G</code> - 315MHz version
* Sensors
* Sensors
** 315MHz
** <code>5Q0-907-275-B</code> / <code>5Q0-907-275-F</code> - 433MHz version
** <code>5Q0-907-275-F</code> - 433MHz version
** <code>5Q0-907-275-C</code> / <code>5Q0-907-275-G</code> - 315MHz version
* Wiring
* Wiring loom
* Bracket
* Bracket
** <code>5NA-907-538-A</code>
** <code>5NA-907-538-A</code>
** <code>4E0-810-675-B</code>
** <code>4E0-810-675-B</code> - Audi RS3 8V
** <code>3G0-907-538</code> - VW Arteon
 
Bracket is optional. Module can be installed inside the car, under the trunk floor.


== Wiring ==
== Wiring ==
=== Vehicle connections ===


* 12V from Terminal30a
* 12V from Terminal30a
** Power from fusebox C, fuse no. 7
** Power from fusebox C, fuse no. 7
* Ground
* Ground
** right side of luggage compartment or other ground point.
** right side of luggage compartment or aby other firm ground point
* CAN-BUS extended from one of listed:
* CAN-BUS extended from TIUL T17d, black 17-pin connector
** TIUL T17d, black 17-pin connector
** Audi A3 8V
*** pin 12 - CAN-BUS EXT, high
*** pin 5 - CAN-BUS EXT, high
*** pin 13 - CAN-BUS EXT, low
*** pin 6 - CAN-BUS EXT, low
 
=== J502 Pinout ===
 
* pin 1 - CAN-BUS EXT, low
* pin 2 - KL30a (+12V)
* pin 3 - CAN-BUS EXT, high
* pin 4 - GND


== Coding ==
== Coding ==


Compiled completed coding guide from public source.
Compiled completed coding guide from public sources.
<ref>https://www.vwvortex.com/threads/retrofit-direct-tpms-guide.9550572/?utm_source=google&utm_medium=organic</ref>
<ref>https://www.vwvortex.com/threads/retrofit-direct-tpms-guide.9550572/?utm_source=google&utm_medium=organic</ref>
<ref>https://www.audizine.com/threads/direct-tpms-retrofit-guide.824924/</ref>
<ref>https://www.audizine.com/threads/direct-tpms-retrofit-guide.824924/</ref>
Line 47: Line 59:
=== Instrument Cluster ===
=== Instrument Cluster ===


// making sure that TPMS LOW is disabled and TPMS HIGH is enabled
  Instrument Cluster (0x17) → Long Coding → Byte 03 → Bit 7 (Tire Pressure Monitoring) → Active
  Instrument Cluster (0x17) → Long Coding → Byte 03 → Bit 7 (Tire Pressure Monitoring) → Active
  Instrument Cluster (0x17) → Long Coding → Byte 04 → Bit 0 (Tire Pressure Monitoring Display) → Inactive
  Instrument Cluster (0x17) → Long Coding → Byte 04 → Bit 0 (Tire Pressure Monitoring Display) → Inactive
Line 72: Line 85:


=== TPMS ===
=== TPMS ===
// In case of Audi S3 8V, there's no need to change anything.


== Firmware ==
== Firmware ==
Line 80: Line 95:
* <code>FL_2H6907273A___ 0003.odx</code> - PQ25, PQ35, PQ47 platforms
* <code>FL_2H6907273A___ 0003.odx</code> - PQ25, PQ35, PQ47 platforms
* <code>FL_3AA907273___0012.odx</code> - PQ25 (gateway 7E0*), PQ35, PQ47 (gateway 7N0*) platforms; works only with 3AA sensors
* <code>FL_3AA907273___0012.odx</code> - PQ25 (gateway 7E0*), PQ35, PQ47 (gateway 7N0*) platforms; works only with 3AA sensors
* <code>FL_4M0907273_0010.odx</code> - Lamborghini
* <code>FL_4M0907273_0010.odx</code> - MLBevo
* <code>FL_5Q0907273___0011.odx</code> - PQ27 and MQB platform
* <code>FL_5Q0907273___0011.odx</code> - PQ27 and MQB platform
* <code>FL_7P6907273L__0003.odx</code>
* <code>FL_7P6907273L__0003.odx</code>
Module that I bought came with <code>4M0</code> firmware and it seams that it works correctly with 2016/17 Audi S3 8V.


== Dataset ==
== Dataset ==
Not required in Audi A3 8V
== OBDeleven scan ==
VIN: WAUZZZ8V5H1035105
Car: _Audi S3 (Matt)
Year: 2017
Body type: Saloon
Engine: DJHA  kW ( hp) l
Mileage: 128401 km
---------------------------------------------------------------
65 Tire Pressure
System description: RDKHUFAU736
Software number: 4M0907273B
Software version: 0010
Hardware number: 4M0907273B
Hardware version: H06
Backup name: Adaptations
Activating and deactivating all development messages
S 100
Not activated
S 101
Not activated
S 102
Not activated
S 103-S 104
Not activated
XCP
Not activated
S 105-S 112
Not activated
Internal fault number
0
Write sensor identification number
Sensor identification number (sensor ID)
0
Wheel position
---
Control module switch-off, switch-off time
Control module
20 min
Data bus
30 min

Latest revision as of 15:57, 15 November 2026

Direct TPMS (Tire Pressure Monitoring System) will measure pressure and temperature inside each wheel. Those measurements are shared with Instrument Cluster and Infotainment.

Based on regional regulations, there are two variations of the system:

7K3 - TPMS High 433MHz
7K4 - TPMS High 315MHz

Parts

[1] [2]

  • Module (J502)
    • 5Q0-907-273-B / 5Q0-907-273-F - 433MHz version
    • 5Q0-907-273-C / 5Q0-907-273-G - 315MHz version
  • Sensors
    • 5Q0-907-275-B / 5Q0-907-275-F - 433MHz version
    • 5Q0-907-275-C / 5Q0-907-275-G - 315MHz version
  • Wiring loom
  • Bracket
    • 5NA-907-538-A
    • 4E0-810-675-B - Audi RS3 8V
    • 3G0-907-538 - VW Arteon

Bracket is optional. Module can be installed inside the car, under the trunk floor.

Wiring

Vehicle connections

  • 12V from Terminal30a
    • Power from fusebox C, fuse no. 7
  • Ground
    • right side of luggage compartment or aby other firm ground point
  • CAN-BUS extended from TIUL T17d, black 17-pin connector
    • Audi A3 8V
      • pin 5 - CAN-BUS EXT, high
      • pin 6 - CAN-BUS EXT, low

J502 Pinout

  • pin 1 - CAN-BUS EXT, low
  • pin 2 - KL30a (+12V)
  • pin 3 - CAN-BUS EXT, high
  • pin 4 - GND

Coding

Compiled completed coding guide from public sources. [3] [4] [5]

Gateway

// configure gateway so it knows that there's new hardware in the CAN-BUS.
Gateway (0x19) → Adaptation → Installation list → Tire Pressure Monitoring 1 → coded

Instrument Cluster

// making sure that TPMS LOW is disabled and TPMS HIGH is enabled
Instrument Cluster (0x17) → Long Coding → Byte 03 → Bit 7 (Tire Pressure Monitoring) → Active
Instrument Cluster (0x17) → Long Coding → Byte 04 → Bit 0 (Tire Pressure Monitoring Display) → Inactive
Instrument Cluster (0x17) → Long Coding → Byte 11 → Bit 2 (Tire Pressure Monitoring BAP) → Active

ABS

// below instruction is for 30-bit version of the ABS module.
// make sure that it applies to your config

// disabling indirect TPMS function
ABS (0x03) → Long Coding → Byte 27 → Bit 4, 5, 6 (TPMS Configuration) → Inactive, Inactive, Inactive
ABS (0x03) → Long Coding → Byte 28 → Bit 7 (TPMS Button BAP) → Inactive

Infotainment

// receiving data on Extended CAN-BUS
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → tire pressure system 0x07 msg bus → Databus Extended
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → tire pressure system 0x07 → Active

// showing GUI in the CAR menu
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk → Activated
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk over threshold high → Activated
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk standstill→ Not activated

TPMS

// In case of Audi S3 8V, there's no need to change anything.

Firmware

Firmware decides how the module works and if it will communicate correctly with rest of the car. [6]

  • FL_2H6907273A___ 0003.odx - PQ25, PQ35, PQ47 platforms
  • FL_3AA907273___0012.odx - PQ25 (gateway 7E0*), PQ35, PQ47 (gateway 7N0*) platforms; works only with 3AA sensors
  • FL_4M0907273_0010.odx - MLBevo
  • FL_5Q0907273___0011.odx - PQ27 and MQB platform
  • FL_7P6907273L__0003.odx

Module that I bought came with 4M0 firmware and it seams that it works correctly with 2016/17 Audi S3 8V.

Dataset

Not required in Audi A3 8V

OBDeleven scan

	VIN: WAUZZZ8V5H1035105
	Car: _Audi S3 (Matt)
	Year: 2017
	Body type: Saloon
	Engine: DJHA  kW ( hp) l
	Mileage: 128401 km

---------------------------------------------------------------

65 Tire Pressure
System description: RDKHUFAU736
Software number: 4M0907273B
Software version: 0010
Hardware number: 4M0907273B
Hardware version: H06
Backup name: Adaptations
	Activating and deactivating all development messages	
		S 100
			Not activated
		S 101
			Not activated
		S 102
			Not activated
		S 103-S 104
			Not activated
		XCP
			Not activated
		S 105-S 112
			Not activated
		Internal fault number
			0
	
	Write sensor identification number	
		Sensor identification number (sensor ID)
			0
		Wheel position
			---
	
	Control module switch-off, switch-off time	
		Control module
			20 min
		Data bus
			30 min