MQB TPMS High retrofit: Difference between revisions
Jump to navigation
Jump to search
Created page with " 7K3 - TPMS High 433MHz Wiring: * Power from fusefolder C, fuse no. 7 * Ground from right side of luggage compartment * CAN-BUS extended from gateway (J533)" |
|||
| (26 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Direct TPMS (Tire Pressure Monitoring System) will measure pressure and temperature inside each wheel. Those measurements are shared with Instrument Cluster and Infotainment. | |||
Based on regional regulations, there are two variations of the system: | |||
7K3 - TPMS High 433MHz | 7K3 - TPMS High 433MHz | ||
7K4 - TPMS High 315MHz | |||
== Parts == | |||
<ref>https://www.audiworld.com/forums/q5-sq5-mkii-discussion-218/za-7k9-tire-pressure-monitoring-system-3017874/</ref> | |||
<ref>https://www.drive2.ru/parts/vag/5q0907273b/B9bkAEAFz1g</ref> | |||
* Module (J502) | |||
** <code>5Q0-907-273-B</code> / <code>5Q0-907-273-F</code> - 433MHz version | |||
** <code>5Q0-907-273-C</code> / <code>5Q0-907-273-G</code> - 315MHz version | |||
* Sensors | |||
** <code>5Q0-907-275-B</code> / <code>5Q0-907-275-F</code> - 433MHz version | |||
** <code>5Q0-907-275-C</code> / <code>5Q0-907-275-G</code> - 315MHz version | |||
* Wiring loom | |||
* Bracket | |||
** <code>5NA-907-538-A</code> | |||
** <code>4E0-810-675-B</code> - Audi RS3 8V | |||
** <code>3G0-907-538</code> - VW Arteon | |||
Bracket is optional. Module can be installed inside the car, under the trunk floor. | |||
== Wiring == | |||
=== Vehicle connections === | |||
* 12V from Terminal30a | |||
** Power from fusebox C, fuse no. 7 | |||
* Ground | |||
** right side of luggage compartment or aby other firm ground point | |||
* CAN-BUS extended from TIUL T17d, black 17-pin connector | |||
** Audi A3 8V | |||
*** pin 5 - CAN-BUS EXT, high | |||
*** pin 6 - CAN-BUS EXT, low | |||
=== J502 Pinout === | |||
* pin 1 - CAN-BUS EXT, low | |||
* pin 2 - KL30a (+12V) | |||
* pin 3 - CAN-BUS EXT, high | |||
* pin 4 - GND | |||
== Coding == | |||
Compiled completed coding guide from public sources. | |||
<ref>https://www.vwvortex.com/threads/retrofit-direct-tpms-guide.9550572/?utm_source=google&utm_medium=organic</ref> | |||
<ref>https://www.audizine.com/threads/direct-tpms-retrofit-guide.824924/</ref> | |||
<ref>https://docs.google.com/spreadsheets/d/1V-OKyWGNWASIKmDf_YrTnT22BEh8ocQ1V1qpXOTBX84/</ref> | |||
=== Gateway === | |||
// configure gateway so it knows that there's new hardware in the CAN-BUS. | |||
Gateway (0x19) → Adaptation → Installation list → Tire Pressure Monitoring 1 → coded | |||
=== Instrument Cluster === | |||
// making sure that TPMS LOW is disabled and TPMS HIGH is enabled | |||
Instrument Cluster (0x17) → Long Coding → Byte 03 → Bit 7 (Tire Pressure Monitoring) → Active | |||
Instrument Cluster (0x17) → Long Coding → Byte 04 → Bit 0 (Tire Pressure Monitoring Display) → Inactive | |||
Instrument Cluster (0x17) → Long Coding → Byte 11 → Bit 2 (Tire Pressure Monitoring BAP) → Active | |||
=== ABS === | |||
// below instruction is for 30-bit version of the ABS module. | |||
// make sure that it applies to your config | |||
// disabling indirect TPMS function | |||
ABS (0x03) → Long Coding → Byte 27 → Bit 4, 5, 6 (TPMS Configuration) → Inactive, Inactive, Inactive | |||
ABS (0x03) → Long Coding → Byte 28 → Bit 7 (TPMS Button BAP) → Inactive | |||
=== Infotainment === | |||
// receiving data on Extended CAN-BUS | |||
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → tire pressure system 0x07 msg bus → Databus Extended | |||
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → tire pressure system 0x07 → Active | |||
// showing GUI in the CAR menu | |||
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk → Activated | |||
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk over threshold high → Activated | |||
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk standstill→ Not activated | |||
=== TPMS === | |||
// In case of Audi S3 8V, there's no need to change anything. | |||
== Firmware == | |||
Firmware decides how the module works and if it will communicate correctly with rest of the car. | |||
<ref>https://www.drive2.ru/parts/vag/5q0907273b/B9bkAEAFz1g</ref> | |||
* <code>FL_2H6907273A___ 0003.odx</code> - PQ25, PQ35, PQ47 platforms | |||
* <code>FL_3AA907273___0012.odx</code> - PQ25 (gateway 7E0*), PQ35, PQ47 (gateway 7N0*) platforms; works only with 3AA sensors | |||
* <code>FL_4M0907273_0010.odx</code> - MLBevo | |||
* <code>FL_5Q0907273___0011.odx</code> - PQ27 and MQB platform | |||
* <code>FL_7P6907273L__0003.odx</code> | |||
Module that I bought came with <code>4M0</code> firmware and it seams that it works correctly with 2016/17 Audi S3 8V. | |||
== Dataset == | |||
Not required in Audi A3 8V | |||
== OBDeleven scan == | |||
VIN: WAUZZZ8V5H1035105 | |||
Car: _Audi S3 (Matt) | |||
Year: 2017 | |||
Body type: Saloon | |||
Engine: DJHA kW ( hp) l | |||
Mileage: 128401 km | |||
--------------------------------------------------------------- | |||
65 Tire Pressure | |||
System description: RDKHUFAU736 | |||
Software number: 4M0907273B | |||
Software version: 0010 | |||
Hardware number: 4M0907273B | |||
Hardware version: H06 | |||
Backup name: Adaptations | |||
Activating and deactivating all development messages | |||
S 100 | |||
Not activated | |||
S 101 | |||
Not activated | |||
S 102 | |||
Not activated | |||
S 103-S 104 | |||
Not activated | |||
XCP | |||
Not activated | |||
S 105-S 112 | |||
Not activated | |||
Internal fault number | |||
0 | |||
Write sensor identification number | |||
Sensor identification number (sensor ID) | |||
0 | |||
Wheel position | |||
--- | |||
Control module switch-off, switch-off time | |||
Control module | |||
20 min | |||
Data bus | |||
30 min | |||
Latest revision as of 15:57, 15 November 2026
Direct TPMS (Tire Pressure Monitoring System) will measure pressure and temperature inside each wheel. Those measurements are shared with Instrument Cluster and Infotainment.
Based on regional regulations, there are two variations of the system:
7K3 - TPMS High 433MHz 7K4 - TPMS High 315MHz
Parts
- Module (J502)
5Q0-907-273-B/5Q0-907-273-F- 433MHz version5Q0-907-273-C/5Q0-907-273-G- 315MHz version
- Sensors
5Q0-907-275-B/5Q0-907-275-F- 433MHz version5Q0-907-275-C/5Q0-907-275-G- 315MHz version
- Wiring loom
- Bracket
5NA-907-538-A4E0-810-675-B- Audi RS3 8V3G0-907-538- VW Arteon
Bracket is optional. Module can be installed inside the car, under the trunk floor.
Wiring
Vehicle connections
- 12V from Terminal30a
- Power from fusebox C, fuse no. 7
- Ground
- right side of luggage compartment or aby other firm ground point
- CAN-BUS extended from TIUL T17d, black 17-pin connector
- Audi A3 8V
- pin 5 - CAN-BUS EXT, high
- pin 6 - CAN-BUS EXT, low
- Audi A3 8V
J502 Pinout
- pin 1 - CAN-BUS EXT, low
- pin 2 - KL30a (+12V)
- pin 3 - CAN-BUS EXT, high
- pin 4 - GND
Coding
Compiled completed coding guide from public sources. [3] [4] [5]
Gateway
// configure gateway so it knows that there's new hardware in the CAN-BUS. Gateway (0x19) → Adaptation → Installation list → Tire Pressure Monitoring 1 → coded
Instrument Cluster
// making sure that TPMS LOW is disabled and TPMS HIGH is enabled Instrument Cluster (0x17) → Long Coding → Byte 03 → Bit 7 (Tire Pressure Monitoring) → Active Instrument Cluster (0x17) → Long Coding → Byte 04 → Bit 0 (Tire Pressure Monitoring Display) → Inactive Instrument Cluster (0x17) → Long Coding → Byte 11 → Bit 2 (Tire Pressure Monitoring BAP) → Active
ABS
// below instruction is for 30-bit version of the ABS module. // make sure that it applies to your config // disabling indirect TPMS function ABS (0x03) → Long Coding → Byte 27 → Bit 4, 5, 6 (TPMS Configuration) → Inactive, Inactive, Inactive ABS (0x03) → Long Coding → Byte 28 → Bit 7 (TPMS Button BAP) → Inactive
Infotainment
// receiving data on Extended CAN-BUS Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → tire pressure system 0x07 msg bus → Databus Extended Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → tire pressure system 0x07 → Active // showing GUI in the CAR menu Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk → Activated Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk over threshold high → Activated Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display rdk standstill→ Not activated
TPMS
// In case of Audi S3 8V, there's no need to change anything.
Firmware
Firmware decides how the module works and if it will communicate correctly with rest of the car. [6]
FL_2H6907273A___ 0003.odx- PQ25, PQ35, PQ47 platformsFL_3AA907273___0012.odx- PQ25 (gateway 7E0*), PQ35, PQ47 (gateway 7N0*) platforms; works only with 3AA sensorsFL_4M0907273_0010.odx- MLBevoFL_5Q0907273___0011.odx- PQ27 and MQB platformFL_7P6907273L__0003.odx
Module that I bought came with 4M0 firmware and it seams that it works correctly with 2016/17 Audi S3 8V.
Dataset
Not required in Audi A3 8V
OBDeleven scan
VIN: WAUZZZ8V5H1035105 Car: _Audi S3 (Matt) Year: 2017 Body type: Saloon Engine: DJHA kW ( hp) l Mileage: 128401 km --------------------------------------------------------------- 65 Tire Pressure System description: RDKHUFAU736 Software number: 4M0907273B Software version: 0010 Hardware number: 4M0907273B Hardware version: H06 Backup name: Adaptations Activating and deactivating all development messages S 100 Not activated S 101 Not activated S 102 Not activated S 103-S 104 Not activated XCP Not activated S 105-S 112 Not activated Internal fault number 0 Write sensor identification number Sensor identification number (sensor ID) 0 Wheel position --- Control module switch-off, switch-off time Control module 20 min Data bus 30 min
- ↑ https://www.audiworld.com/forums/q5-sq5-mkii-discussion-218/za-7k9-tire-pressure-monitoring-system-3017874/
- ↑ https://www.drive2.ru/parts/vag/5q0907273b/B9bkAEAFz1g
- ↑ https://www.vwvortex.com/threads/retrofit-direct-tpms-guide.9550572/?utm_source=google&utm_medium=organic
- ↑ https://www.audizine.com/threads/direct-tpms-retrofit-guide.824924/
- ↑ https://docs.google.com/spreadsheets/d/1V-OKyWGNWASIKmDf_YrTnT22BEh8ocQ1V1qpXOTBX84/
- ↑ https://www.drive2.ru/parts/vag/5q0907273b/B9bkAEAFz1g