MQB Side Assist retrofit: Difference between revisions

From mr-fix.info Wiki
Jump to navigation Jump to search
 
(8 intermediate revisions by the same user not shown)
Line 7: Line 7:


=== Audi A3 8V ===
=== Audi A3 8V ===
Radars:
Radar modules:
* <code>3Q0-907-566-D/F/H/J</code> - radar module (J769 -MASTER-), right, facelift
* facelift
* <code>3Q0-907-590-D/F/H/J</code> - radar module (J770 -SLAVE-), left, facelift
** <code>3Q0-907-566-D/F/H/J</code> - J769 -MASTER-, right
** <code>3Q0-907-590-D/F/H/J</code> - J770 -SLAVE-, left


Mounting brackets:
It was reported that both radar modules need to have the same suffix letter in order to work properly. Not sure if the firmware can be flashed in order to create a pair of working modules.
* 8V5 907 175 - radar mounting bracket, left, sedan
* 8V5 907 176 - radar mounting bracket, right, sedan


Indicators:
Mounting brackets for radars:
* <code>8V1-949-145</code> - Mirror indicator, left, before facelift, LHD
* facelift, sedan
* <code>8V1-949-146</code> - Mirror indicator, right, before facelift, LHD
** <code>8V5-907-175</code> - left
** <code>8V5-907-176</code> - right


* <code>8V2-949-145</code> - Mirror indicator, left, before facelift, RHD
Mirror indicators:
* <code>8V2-949-146</code> - Mirror indicator, right, before facelift, RHD
* before facelift, LHD
** <code>8V1-949-145</code> - left
** <code>8V1-949-146</code> - right


* <code>8V1-949-145-A</code> - Mirror indicator, left, facelift, LHD
* before facelift, RHD
* <code>8V1-949-146-A</code> - Mirror indicator, right, facelift, LHD
** <code>8V2-949-145</code> - left
** <code>8V2-949-146</code> - right


* <code>8V2-949-145-A</code> - Mirror indicator, left, facelift, RHD
* facelift, LHD
* <code>8V2-949-146-A</code> - Mirror indicator, right, facelift, RHD
** <code>8V1-949-145-A</code> - left
** <code>8V1-949-146-A</code> - right
 
* facelift, RHD
** <code>8V2-949-145-A</code> - left
** <code>8V2-949-146-A</code> - right


Mirror Caps:
Mirror Caps:
Line 36: Line 44:


== Wiring ==
== Wiring ==
=== Vehicle connections ===
* 12V from Terminal15
** Power from fusebox C, fuse no. 32 via W10 interior light wiring harness
* Ground
** right side of luggage compartment or any other firm ground point
* CAN-BUS extended from TIUL T17d, black 17-pin connector
** Audi A3 8V
*** pin 5 - CAN-BUS EXT, high
*** pin 6 - CAN-BUS EXT, low
=== J769 ===
* T8/1 - GND
* T8/2 - CAN-BUS EXT, high
* T8/3 - CAN-BUS EXT, low
* T8/4 - Right Indicator
* T8/5 - To J770
* T8/6 - To J770
* T8/7 - Right Indicator
* T8/8 - TERM15 interior light wiring harness
=== J770 ===
* T8/1 - GND
* T8/2 - CAN-BUS EXT, high
* T8/3 - CAN-BUS EXT, low
* T8/4 - Left Indicator
* T8/5 - To J769
* T8/6 - To J769
* T8/7 - Left Indicator
* T8/8 - TERM15 interior light wiring harness


== Firmware ==
== Firmware ==
//TODOOO


== Coding ==
== Coding ==
Line 43: Line 84:
Compiled completed coding guide from public sources.
Compiled completed coding guide from public sources.
<ref>https://forums.ross-tech.com/index.php?threads/36746/</ref>
<ref>https://forums.ross-tech.com/index.php?threads/36746/</ref>
<ref>https://docs.google.com/spreadsheets/d/1V-OKyWGNWASIKmDf_YrTnT22BEh8ocQ1V1qpXOTBX84/</ref>


=== Gateway ===
=== Gateway ===


  // configure gateway so it knows that there's new hardware in the CAN-BUS.
  // configure gateway so it knows that there's new hardware in the CAN-BUS.
  Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant → coded
  Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant → Coded
  Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant 2 → coded
  Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant 2 → Coded
 
=== ABS ===
 
// below instruction is for 30-bit version of the ABS module.
// make sure that it applies to your config
ABS (0x03) → Long Coding → Byte 29 → Bit 7 (RCTA, Installed) → Enable
 
=== Park Assist ===
 
Park Assist (0x10 or 0x76) → Long Coding → Byte 03 → Bit 6 (RTCA warning level, installed) → Enable


=== Instrument Cluster ===
=== Instrument Cluster ===
Line 57: Line 110:
=== Lane Change Assistant ===
=== Lane Change Assistant ===


// Enabling Rear Cross-Traffic Assist
  Lane Change Assistant (0x3C) → Long Coding → Byte 00 → Bit 2 (RTCA, active) → Enable
  Lane Change Assistant (0x3C) → Long Coding → Byte 00 → Bit 2 (RTCA, active) → Enable
  Lane Change Assistant (0x3C) → Long Coding → Byte 02 → Bits 0-7 (?) → Enable
  Lane Change Assistant (0x3C) → Long Coding → Byte 02 → Bits 0-7 (RCTA Tone) → Tone via PLA
 
=== Infotainment ===
 
// receiving data
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A msg bus → Terminal 15
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A → Active
// showing GUI in the CAR menu
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant → Activated
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant over threshold high → Activated
 
=== Assistnat Camera ===
 
Assistnat Camera (0xA5) → Long Coding → Byte ?? → Bit ? (SWA, coded) → Enable
 
== Component Protection ==


// TODOOO
== Basic Settings ==
== Basic Settings ==
// TODOOO

Latest revision as of 17:27, 15 November 2026

7Y1	- Lane change assist		
79B	- Lane change system, lane keeping system and traffic jam assist
79D	- Lane change assist, lane keeping system, traffic jam assist, and emergency assist
7Y5 	- Lane change system, lane keeping system / lane departure warning

Parts

Audi A3 8V

Radar modules:

  • facelift
    • 3Q0-907-566-D/F/H/J - J769 -MASTER-, right
    • 3Q0-907-590-D/F/H/J - J770 -SLAVE-, left

It was reported that both radar modules need to have the same suffix letter in order to work properly. Not sure if the firmware can be flashed in order to create a pair of working modules.

Mounting brackets for radars:

  • facelift, sedan
    • 8V5-907-175 - left
    • 8V5-907-176 - right

Mirror indicators:

  • before facelift, LHD
    • 8V1-949-145 - left
    • 8V1-949-146 - right
  • before facelift, RHD
    • 8V2-949-145 - left
    • 8V2-949-146 - right
  • facelift, LHD
    • 8V1-949-145-A - left
    • 8V1-949-146-A - right
  • facelift, RHD
    • 8V2-949-145-A - left
    • 8V2-949-146-A - right

Mirror Caps:

  • 8V0-857-527-E - Mirror Cap, left
  • 8V0-857-528-E - Mirror Cap, right

Wiring Loom:

  • 8V0-971-104-N - Wiring harness, sedan, with 6 PDC sensors

Wiring

Vehicle connections

  • 12V from Terminal15
    • Power from fusebox C, fuse no. 32 via W10 interior light wiring harness
  • Ground
    • right side of luggage compartment or any other firm ground point
  • CAN-BUS extended from TIUL T17d, black 17-pin connector
    • Audi A3 8V
      • pin 5 - CAN-BUS EXT, high
      • pin 6 - CAN-BUS EXT, low

J769

  • T8/1 - GND
  • T8/2 - CAN-BUS EXT, high
  • T8/3 - CAN-BUS EXT, low
  • T8/4 - Right Indicator
  • T8/5 - To J770
  • T8/6 - To J770
  • T8/7 - Right Indicator
  • T8/8 - TERM15 interior light wiring harness

J770

  • T8/1 - GND
  • T8/2 - CAN-BUS EXT, high
  • T8/3 - CAN-BUS EXT, low
  • T8/4 - Left Indicator
  • T8/5 - To J769
  • T8/6 - To J769
  • T8/7 - Left Indicator
  • T8/8 - TERM15 interior light wiring harness


Firmware

//TODOOO

Coding

Compiled completed coding guide from public sources. [1] [2]

Gateway

// configure gateway so it knows that there's new hardware in the CAN-BUS.
Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant → Coded
Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant 2 → Coded

ABS

// below instruction is for 30-bit version of the ABS module.
// make sure that it applies to your config

ABS (0x03) → Long Coding → Byte 29 → Bit 7 (RCTA, Installed) → Enable

Park Assist

Park Assist (0x10 or 0x76) → Long Coding → Byte 03 → Bit 6 (RTCA warning level, installed) → Enable

Instrument Cluster

Instrument Cluster (0x17) → Long Coding → Byte 05 → Bit 3 (Lane Change Assistant, installed) → Enable
Instrument Cluster (0x17) → Long Coding → Byte 11 → Bit 3 (Lane Change Assistant, BAP distance) → Enable

Lane Change Assistant

// Enabling Rear Cross-Traffic Assist
Lane Change Assistant (0x3C) → Long Coding → Byte 00 → Bit 2 (RTCA, active) → Enable
Lane Change Assistant (0x3C) → Long Coding → Byte 02 → Bits 0-7 (RCTA Tone) → Tone via PLA

Infotainment

// receiving data
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A msg bus → Terminal 15
Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A → Active

// showing GUI in the CAR menu
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant → Activated
Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant over threshold high → Activated

Assistnat Camera

Assistnat Camera (0xA5) → Long Coding → Byte ?? → Bit ? (SWA, coded) → Enable

Component Protection

// TODOOO

Basic Settings

// TODOOO