MQB Side Assist retrofit
7Y1 - Lane change assist 79B - Lane change system, lane keeping system and traffic jam assist 79D - Lane change assist, lane keeping system, traffic jam assist, and emergency assist 7Y5 - Lane change system, lane keeping system / lane departure warning
Parts
Audi A3 8V
Radars:
3Q0-907-566-D/F/H/J- radar module (J769 -MASTER-), right, facelift3Q0-907-590-D/F/H/J- radar module (J770 -SLAVE-), left, facelift
It was reported that both radar modules need to have the same suffix letter in order to work properly. Not sure if the firmware can be flashed in order to create a pair of working modules.
Mounting brackets for radars:
- facelift, sedan
8V5-907-175- left8V5-907-176- right
- facelift, hatchback
TODOOO
- facelift, cabrio
TODOOO
Mirror indicators:
- before facelift, LHD
8V1-949-145- left8V1-949-146- right
- before facelift, RHD
8V2-949-145- left8V2-949-146- right
- facelift, LHD
8V1-949-145-A- left8V1-949-146-A- right
- facelift, RHD
8V2-949-145-A- left8V2-949-146-A- right
Mirror Caps:
8V0-857-527-E- Mirror Cap, left8V0-857-528-E- Mirror Cap, right
Wiring Loom:
8V0-971-104-N- Wiring harness, sedan, with 6 PDC sensors
Wiring
Vehicle connections
- 12V from Terminal15
- Power from fusebox C, fuse no. 32 via W10 interior light wiring harness
- Ground
- right side of luggage compartment or any other firm ground point
- CAN-BUS extended from TIUL T17d, black 17-pin connector
- Audi A3 8V
- pin 5 - CAN-BUS EXT, high
- pin 6 - CAN-BUS EXT, low
- Audi A3 8V
J769
- T8/1 - GND
- T8/2 - CAN-BUS EXT, high
- T8/3 - CAN-BUS EXT, low
- T8/4 - Right Indicator
- T8/5 - To J770
- T8/6 - To J770
- T8/7 - Right Indicator
- T8/8 - TERM15 interior light wiring harness
J770
- T8/1 - GND
- T8/2 - CAN-BUS EXT, high
- T8/3 - CAN-BUS EXT, low
- T8/4 - Left Indicator
- T8/5 - To J769
- T8/6 - To J769
- T8/7 - Left Indicator
- T8/8 - TERM15 interior light wiring harness
Firmware
//TODOOO
Coding
Compiled completed coding guide from public sources. [1] [2]
Gateway
// configure gateway so it knows that there's new hardware in the CAN-BUS. Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant → Coded Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant 2 → Coded
ABS
// below instruction is for 30-bit version of the ABS module. // make sure that it applies to your config ABS (0x03) → Long Coding → Byte 29 → Bit 7 (RCTA, Installed) → Enable
Park Assist
Park Assist (0x10 or 0x76) → Long Coding → Byte 03 → Bit 6 (RTCA warning level, installed) → Enable
Instrument Cluster
Instrument Cluster (0x17) → Long Coding → Byte 05 → Bit 3 (Lane Change Assistant, installed) → Enable Instrument Cluster (0x17) → Long Coding → Byte 11 → Bit 3 (Lane Change Assistant, BAP distance) → Enable
Lane Change Assistant
// Enabling Rear Cross-Traffic Assist Lane Change Assistant (0x3C) → Long Coding → Byte 00 → Bit 2 (RTCA, active) → Enable Lane Change Assistant (0x3C) → Long Coding → Byte 02 → Bits 0-7 (RCTA Tone) → Tone via PLA
Infotainment
// receiving data Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A msg bus → Terminal 15 Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A → Active // showing GUI in the CAR menu Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant → Activated Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant over threshold high → Activated
Assistnat Camera
Assistnat Camera (0xA5) → Long Coding → Byte ?? → Bit ? (SWA, coded) → Enable
Component Protection
// TODOOO
Basic Settings
// TODOOO