MQB Side Assist retrofit
7Y1 - Lane change assist 79B - Lane change system, lane keeping system and traffic jam assist 79D - Lane change assist, lane keeping system, traffic jam assist, and emergency assist 7Y5 - Lane change system, lane keeping system / lane departure warning
Parts
Audi A3 8V
Radars:
3Q0-907-566-D/F/H/J- radar module (J769 -MASTER-), right, facelift3Q0-907-590-D/F/H/J- radar module (J770 -SLAVE-), left, facelift
Mounting brackets:
- 8V5 907 175 - radar mounting bracket, left, sedan
- 8V5 907 176 - radar mounting bracket, right, sedan
Indicators:
8V1-949-145- Mirror indicator, left, before facelift, LHD8V1-949-146- Mirror indicator, right, before facelift, LHD
8V2-949-145- Mirror indicator, left, before facelift, RHD8V2-949-146- Mirror indicator, right, before facelift, RHD
8V1-949-145-A- Mirror indicator, left, facelift, LHD8V1-949-146-A- Mirror indicator, right, facelift, LHD
8V2-949-145-A- Mirror indicator, left, facelift, RHD8V2-949-146-A- Mirror indicator, right, facelift, RHD
Mirror Caps:
8V0-857-527-E- Mirror Cap, left8V0-857-528-E- Mirror Cap, right
Wiring Loom:
8V0-971-104-N- Wiring harness, sedan, with 6 PDC sensors
Wiring
//TODOOO
Firmware
Coding
Compiled completed coding guide from public sources. [1] [2]
Gateway
// configure gateway so it knows that there's new hardware in the CAN-BUS. Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant → Coded Gateway (0x19) → Adaptation → Installation list → Lane Change Assistant 2 → Coded
ABS
// below instruction is for 30-bit version of the ABS module. // make sure that it applies to your config ABS (0x03) → Long Coding → Byte 29 → Bit 7 (RCTA, Installed) → Enable
Park Assist
Park Assist (0x10 or 0x76) → Long Coding → Byte 03 → Bit 6 (RTCA warning level, installed) → Enable
Instrument Cluster
Instrument Cluster (0x17) → Long Coding → Byte 05 → Bit 3 (Lane Change Assistant, installed) → Enable Instrument Cluster (0x17) → Long Coding → Byte 11 → Bit 3 (Lane Change Assistant, BAP distance) → Enable
Lane Change Assistant
// Enabling Rear Cross-Traffic Assist Lane Change Assistant (0x3C) → Long Coding → Byte 00 → Bit 2 (RTCA, active) → Enable Lane Change Assistant (0x3C) → Long Coding → Byte 02 → Bits 0-7 (RCTA Tone) → Tone via PLA
Infotainment
// receiving data Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A msg bus → Terminal 15 Infotainment (0x5F) → Adaptation → Car Function List BAP Gen2 → SWA 0x1A → Active // showing GUI in the CAR menu Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant → Activated Infotainment (0x5F) → Adaptation → Car Function Adaptations Gen2 → Menu display lane assistant over threshold high → Activated
Assistnat Camera
Assistnat Camera (0xA5) → Long Coding → Byte ?? → Bit ? (SWA, coded) → Enable
Component Protection
// TODOOO
Basic Settings
// TODOOO